- -

Tribological Behavior of New Martensitic Stainless Steels Using Scratch and Dry Wear Test

RiuNet: Repositorio Institucional de la Universidad Politécnica de Valencia

Compartir/Enviar a

Citas

Estadísticas

  • Estadisticas de Uso

Tribological Behavior of New Martensitic Stainless Steels Using Scratch and Dry Wear Test

Mostrar el registro sencillo del ítem

Ficheros en el ítem

[Cerrado]
Nombre: ALBA;W. Rimli;D. ...
Tamaño: 5.142Mb
Formato: PDF
Descripción: Versión editorial
Solicitar una copia al autor
dc.contributor.author Dalmau Borrás, Alba es_ES
dc.contributor.author Rmili, W. es_ES
dc.contributor.author Joly, D. es_ES
dc.contributor.author Richard, C. es_ES
dc.contributor.author Igual Muñoz, Anna Neus es_ES
dc.date.accessioned 2016-10-06T12:25:58Z
dc.date.available 2016-10-06T12:25:58Z
dc.date.issued 2014-12
dc.identifier.issn 1023-8883
dc.identifier.uri http://hdl.handle.net/10251/71310
dc.description.abstract This paper focuses on the tribological characterization of new martensitic stainless steels by two different tribological methods (scratch and dry wear tests) and their comparison to the austenitic standard stainless steel AISI 316L. The scratch test allows obtaining critical loads, scratch friction coefficients, scratch hardness and specific scratch wear rate, and the dry wear test to quantify wear volumes. The damage has been studied by ex situ scanning electron microscopy. Wear resistance was related to the hardness and the microstructure of the studied materials, where martensitic stainless steels exhibit higher scratch wear resistance than the austenitic one, but higher hardness of the martensitic alloys did not give better scratch resistance when comparing with themselves. It has been proved it is possible to evaluate the scratch wear resistance of bulk stainless steels using scratch test. The austenitic material presented lower wear volume than the martensitic ones after the dry wear test due to phase transformation and the hardening during sliding. es_ES
dc.description.sponsorship The authors would like to thank to BPI, Region Centre and Tours Plus for support of this research, and also to Aubert and Duval and UF1 for providing the materials of this study. This work is done under the project FUI 11 Mekinox. We also wish to appreciate the helpful advice from Aubert and Duval. en_EN
dc.language Inglés es_ES
dc.publisher Springer Verlag es_ES
dc.relation.ispartof Tribology Letters es_ES
dc.rights Reserva de todos los derechos es_ES
dc.subject Martensitic stainless steels es_ES
dc.subject Scratch es_ES
dc.subject Bulk material es_ES
dc.subject Dry wear test es_ES
dc.subject tribology es_ES
dc.subject.classification INGENIERIA QUIMICA es_ES
dc.title Tribological Behavior of New Martensitic Stainless Steels Using Scratch and Dry Wear Test es_ES
dc.type Artículo es_ES
dc.identifier.doi 10.1007/s11249-014-0429-6
dc.rights.accessRights Cerrado es_ES
dc.contributor.affiliation Universitat Politècnica de València. Instituto de Seguridad Industrial, Radiofísica y Medioambiental - Institut de Seguretat Industrial, Radiofísica i Mediambiental es_ES
dc.contributor.affiliation Universitat Politècnica de València. Departamento de Ingeniería Química y Nuclear - Departament d'Enginyeria Química i Nuclear es_ES
dc.description.bibliographicCitation Dalmau Borrás, A.; Rmili, W.; Joly, D.; Richard, C.; Igual Muñoz, AN. (2014). Tribological Behavior of New Martensitic Stainless Steels Using Scratch and Dry Wear Test. Tribology Letters. 56(3):517-529. doi:10.1007/s11249-014-0429-6 es_ES
dc.description.accrualMethod S es_ES
dc.relation.publisherversion http://dx.doi.org/10.1007/s11249-014-0429-6 es_ES
dc.description.upvformatpinicio 517 es_ES
dc.description.upvformatpfin 529 es_ES
dc.type.version info:eu-repo/semantics/publishedVersion es_ES
dc.description.volume 56 es_ES
dc.description.issue 3 es_ES
dc.relation.senia 284065 es_ES
dc.description.references Kwok, C.T., Lo, K.H., Cheng, F.T., Man, H.C.: Effect of processing conditions on the corrosion performance of laser surface-melted AISI 440C martensitic stainless steel. Surf. Coat. Technol. 166, 221–230 (2003) es_ES
dc.description.references Cheng, Z., Li, C.X., Dong, H., Bell, T.: Low temperature plasma nitrocarburising of AISI 316 austenitic stainless steel. Surf. Coat. Technol. 191, 195–200 (2005) es_ES
dc.description.references Ma, X.P., Wang, L.J., Liu, C.M., Subramanian, S.V.: Microstructure and properties of 13Cr5Ni1Mo0.025Nb0.09V0.06 N super martensitic stainless steel. Mater. Sci. Eng., A 539, 271–279 (2012) es_ES
dc.description.references Thibault, D., Bocher, P., Thomas, M.: Residual stress and microstructure in welds of 13%Cr–4%Ni martensitic stainless steel. J. Mater. Process. Technol. 209, 2195–2202 (2009) es_ES
dc.description.references Li, C.X., Bell, T.: Corrosion properties of plasma nitrided AISI 410 martensitic stainless steel in 3.5 % NaCl and 1 % HCl aqueous solutions. Corros. Sci. 48, 2036–2049 (2006) es_ES
dc.description.references Puli, R., Janaki Ram, G.D.: Microstructures and properties of friction surfaced coatings in AISI 440C martensitic stainless steel. Surf. Coat. Technol 207, 310–318 (2012) es_ES
dc.description.references Garcideandrés, C., Caruana, G., Alvarez, L.F.: Control of M23C6 carbides in 0.45C–13Cr martensitic stainless steel by means of three representative heat treatment parameters. Mater. Sci. Eng., A 241, 211–215 (1998) es_ES
dc.description.references Mahmoudi, A., Ghavidel, M.R.Z., Nedjad, S.H., Heidarzadeh, A., Ahmadabadi, M.N.: Aging behavior and mechanical properties of maraging steels in the presence of submicrocrystalline Laves phase particles. Mater. Charact. 62, 976–981 (2011) es_ES
dc.description.references Meshram, S.D., Madhusudhan Reddy, G., Pandey, S.: Friction stir welding of maraging steel (Grade-250). Mater. Des. 49, 58–64 (2013) es_ES
dc.description.references Jiang, H., Browning, R., Sue, H.-J.: Understanding of scratch-induced damage mechanisms in polymers. Polymer (Guildf). 50, 4056–4065 (2009) es_ES
dc.description.references Bull, S.J., Berasetegui, E.G.: An overview of the potential of quantitative coating adhesion measurement by scratch testing. Tribol. Int. 39, 99–114 (2006) es_ES
dc.description.references Rodrigo, A., Ichimura, H.: Analytical correlation of hardness and scratch adhesion for hard films. Surf. Coat. Technol. 148, 8–17 (2001) es_ES
dc.description.references Rudermann, Y., Iost, A., Bigerelle, M.: Scratch tests to contribute designing performance maps of multilayer polymeric coatings. Tribol. Int. 44, 585–591 (2011) es_ES
dc.description.references Browning, R., Sue, H.-J., Minkwitz, R., Charoensirisomboon, P.: Effects of acrylonitrile content and molecular weight on the scratch behavior of styrene-acrylonitrile random copolymers. Polym. Eng. Sci. 51, 2282–2294 (2011) es_ES
dc.description.references Petit, F., Ott, C., Cambier, F.: Multiple scratch tests and surface-related fatigue properties of monolithic ceramics and soda lime glass. J. Eur. Ceram. Soc. 29, 1299–1307 (2009) es_ES
dc.description.references Friedrich, K., Sue, H.J., Liu, P., Almajid, A.A.: Scratch resistance of high performance polymers. Tribol. Int. 44, 1032–1046 (2011) es_ES
dc.description.references Xiang, C., Sue, H.J., Chu, J., Coleman, B.: Scratch behavior and material property relationship in polymers. J. Polym. Sci., Part B: Polym. Phys. 39, 47–59 (2001) es_ES
dc.description.references Choi, W.-J., Lee, J.H., Weon, J.-I.: Effects of photodegradation and thermal ageing on the scratch behavior of uncoated thermoplastic olefin. Tribol. Int. 67, 90–97 (2013) es_ES
dc.description.references Bull, S.J.: Failure mode maps in the thin film scratch adhesion test. Tribol. Int. 30, 491–498 (1997) es_ES
dc.description.references Bull, S.J.: Can scratch testing be used as a model for the abrasive wear of hard coatings? Wear 233–235, 412–423 (1999) es_ES
dc.description.references Sander, T., Tremmel, S., Wartzack, S.: A modified scratch test for the mechanical characterization of scratch resistance and adhesion of thin hard coatings on soft substrates. Surf. Coat. Technol. 206, 1873–1878 (2011) es_ES
dc.description.references Lin, J.-S., Zhou, Y.: Can scratch tests give fracture toughness? Eng. Fract. Mech. 109, 161–168 (2013) es_ES
dc.description.references Akono, A.-T., Ulm, F.-J.: Scratch test model for the determination of fracture toughness. Eng. Fract. Mech. 78, 334–342 (2011) es_ES
dc.description.references Beake, B.D., Liskiewicz, T.W.: Comparison of nano-fretting and nano-scratch tests on biomedical materials. Tribol. Int. 63, 123–131 (2013) es_ES
dc.description.references ASTM International, ASTM C1624–05. Standard test method for adhesion making potentiostatic and potentiodynamic anodic polarization measurements, 2010: ASTM International, ASTM C1624–05. Standard test method for adhesion making potentiostatic and potentiodynamic anodic polarization measurements, 2010 es_ES
dc.description.references Kurkcu, P., Andena, L., Pavan, A.: An experimental investigation of the scratch behaviour of polymers: 1. Influence of rate-dependent bulk mechanical properties. Wear 290–291, 86–93 (2012) es_ES
dc.description.references Francois, R.: Métallurgie et traitement thermique de nouveaux aciers maraging. Trait. Therm. 390, 51–56 (2008) es_ES
dc.description.references Samuels, L.E.: Light Microscopy of Carbon Steels. Materials Park, Ohio: ASM International, c1999. (199)AD es_ES
dc.description.references Tsakiris, V., Edmonds, D.V.: Martensite and deformation twinning in austenitic steels. Mater. Sci. Eng., A 273–275, 430–436 (1999) es_ES
dc.description.references Tong, Z., Ding, C., Yan, D.: A fracture model for wear mechanism in plasma sprayed ceramic coating materials. Wear 155, 309–316 (1992) es_ES
dc.description.references Vargonen, M., Yang, Y., Huang, L., Shi, Y.: Molecular simulation of tip wear in a single asperity sliding contact. Wear 307, 150–154 (2013) es_ES
dc.description.references Farias, M.C.M., Souza, R.M., Sinatora, A., Tanaka, D.K.: The influence of applied load, sliding velocity and martensitic transformation on the unlubricated sliding wear of austenitic stainless steels. Wear 263, 773–781 (2007) es_ES
dc.description.references Zandrahimi, M., Bateni, M.R., Poladi, A., Szpunar, J.A.: The formation of martensite during wear of AISI 304 stainless steel. Wear 263, 674–678 (2007) es_ES
dc.description.references Misra, R.D.K., Venkatsurya, P., Wu, K.M., Karjalainen, L.P.: Ultrahigh strength martensite–austenite dual-phase steels with ultrafine structure: the response to indentation experiments. Mater. Sci. Eng., A 560, 693–699 (2013) es_ES
dc.description.references Song, E.P., Hwang, B., Lee, S., Kim, N.J., Ahn, J.: Correlation of microstructure with hardness and wear resistance of stainless steel blend coatings fabricated by atmospheric plasma spraying. Mater. Sci. Eng., A 429, 189–195 (2006) es_ES


Este ítem aparece en la(s) siguiente(s) colección(ones)

Mostrar el registro sencillo del ítem