Domínguez-Candela, Iván; Ferri Azor, José Miguel; Cardona, S. C.; Lora-García, Jaime; Fombuena, Vicent(MDPI AG, 2021-04)
[EN] The use of a new bio-based plasticizer derived from epoxidized chia seed oil (ECO) was applied in a poly(lactic acid) (PLA) matrix. ECO was used due to its high epoxy content (6.7%), which led to an improved chemical ...
[EN] The present study describes the preparation and characterization of binary and ternary blends based on polylactide (PLA) with poly("-caprolactone) (PCL) and thermoplastic starch (TPS) to develop fully compostable ...
[EN] Phenolic acids (ferulic, p-coumaric, and protocatechuic) have been incorporated into polylactic (PLA): Poly(3hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) (75:25) blend films that were obtained by melt-blending and ...
In this paper the processing and properties of flexible electrospun biocomposites based on poly(lactic acid) (PLA) blended with 25 wt% of poly(hydroxybutyrate) (PHB), plasticized with 15 wt% of acetyl(tributyl citrate) ...
[EN] Green composites made of polylactide (PLA) filled with almond shell flour (ASF) at a constant weight content of 25¿wt.-% were manufactured by injection molding. In order to increase the interfacial adhesion between ...
[EN] The purpose of this paper is to study and outline the effects of infill parameters (percentage and pattern) using fused deposition manufacturing on mechanical properties of PLA printed samples.
Three infill patterns ...
Cerdá Gandía, Raúl(Universitat Politècnica de València, 2020-09-08)
[ES] El objetivo del TFM es la obtención de films de PLA con aceites esenciales encapsulados en su interior que vayan liberando sus principios activos con el tiempo.
Se va a llevar a cabo una revisión bibliográfica de ...
[EN] Thiswork reports the effect of acrylated epoxidized soybean oil (AESO) addition on the mechanical, thermal, and thermomechanical properties of polylactide (PLA) parts obtained by injection molding. To this end, AESO, ...
Miralles Méndez, Sara(Universitat Politècnica de València, 2019-10-07)
[ES] La fabricación aditiva es una tecnología de fabricación que está revolucionando rápidamente la industria y sus procesos. Sin embargo, todavía es necesario trabajar más en su regulación, trazabilidad y en los parámetros ...
García Campo, María Jesús; Quiles-Carrillo, Luis; Masiá Vañó, Jaime; Reig-Pérez, Miguel Jorge; Montanes, Nestor; Balart, Rafael(MDPI AG, 2017)
[EN] Ternary blends of poly(lactic acid) (PLA), poly(3-hydroxybutyrate) (PHB) and poly(e-caprolactone) (PCL) with a constant weight percentage of 60%, 10% and 30% respectively were compatibilized with soybean oil derivatives ...
Morcillo Esquerdo, María del Carmen(Universitat Politècnica de València, 2020-01-30)
[ES] El principal objetivo abordado en el proyecto ha sido el uso de PLA 2003D y su reutilización hasta seis ciclos de procesado. Posteriormente se procedió a estudiar sus características mecánicas, térmicas, termomecánicas, ...
Gregorio Collazo, Manuel(Universitat Politècnica de València, 2022-09-05)
[ES] El proceso de regeneración de tractos neurales formados por axones puede ser asistido mediante biomateriales (scaffolds) que sirvan de soporte de crecimiento y guía estructural. En el trabajo se realizará un estudio ...
Silvestre Florencio, Rocío(Universitat Politècnica de València, 2021-10-04)
[ES] El trabajo se desarrolla con el objetivo de conocer la capacidad de adhesión de
los polímeros de impresión aditiva sobre diversos sustratos textiles.
Debido a la amplitud del estudio, el alcance se reduce al ácido ...
Moraga Ramón, Giovanni(Universitat Politècnica de València, 2019-02-28)
[ES] El objetivo central del proyecto es el desarrollo de polímeros con memoria de forma utilizando como base poli(ácido láctico) PLA. No obstante, debido a su rigidez y fragilidad, se abordará la mejora en las propiedades ...
[EN] Green composites made of polylactide (PLA) and short flaxseed fibers (FFs) at 20 wt % were successfully compounded by twin-screw extrusion (TSE) and subsequently shaped into pieces by injection molding. The linen waste ...
Muller, Justine(Universitat Politècnica de València, 2017-10-13)
Biodegradable active films based on poly(lactic) acid (PLA) and starch were developed and characterized as to their functional and structural properties, using the bilayer film strategy, in order to obtain materials that ...
Giménez Sanchis, Adrián(Universitat Politècnica de València, 2019-10-10)
[ES] Se estudió la efectividad de la incorporación de agentes de refuerzo celulósicos y extracto acuoso antioxidante (AE) provenientes de cascarilla de café para mejorar las propiedades funcionales de las películas de ...
Rosales Morales, Sara(Universitat Politècnica de València, 2016-11-09)
[ES] Este Trabajo de Fin de Grado consiste en, mediante la tecnología FDM (Fused
Deposition Modeling), realizar un estudio de generación de soportes solubles con
impresora 3D de doble cabezal. Se estudiará las variables ...
Juárez Varón, David; Balart Gimeno, Rafael Antonio; Sánchez Llopis, Miguel; Mengual Recuerda, Ana(Área de Innovación y Desarrollo, S.L., 2015-09-10)
[EN] This study aims to obtain Green Composites formed with a PLA matrix and fiber plant Posidonia and compare them with the mechanical properties of virgin PLA. Therefore, we have studied the influence of the coupling ...
Aldás-Carrasco, Miguel Fernando; Ferri, J. M.; Motoc, Dana Luca; PEPONI, LAURA; Arrieta, Marina Patricia; López-Martínez, Juan(MDPI AG, 2021-06)
[EN] Gum rosin (GR) was used as a natural additive to improve the compatibility between polylactic acid, PLA, and poly(butylene adipate-co-terephthalate, PBAT, blended with 20 wt.% of PBAT (PLA/PBAT). The PBAT was used as ...