- -

Analysis of the feeding system in the injection process of peek in fixed partial dentures

RiuNet: Repositorio Institucional de la Universidad Politécnica de Valencia

Compartir/Enviar a

Citas

Estadísticas

  • Estadisticas de Uso

Analysis of the feeding system in the injection process of peek in fixed partial dentures

Mostrar el registro sencillo del ítem

Ficheros en el ítem

Thumbnail
Nombre: 1-s2.0-S187770581 ...
Tamaño: 1.079Mb
Formato: PDF
Descripción: Versión editorial
Abrir
dc.contributor.author Gutiérrez, S. C. es_ES
dc.contributor.author Meseguer, M. D. es_ES
dc.contributor.author Gandía Barberá, Alejandro es_ES
dc.date.accessioned 2018-04-14T04:16:50Z
dc.date.available 2018-04-14T04:16:50Z
dc.date.issued 2015 es_ES
dc.identifier.issn 1877-7058 es_ES
dc.identifier.uri http://hdl.handle.net/10251/100416
dc.description.abstract [EN] In dental sector, PEEK is a new material used in the injection process of fixed partial dentures (FPD). The design of the feeding system is one of the most important stages in the injection process. This study simulates different locations of the feeding system in fixed partial dentures of PEEK, varying number of the injection points, using the software Moldflow. Variables used to compare simulations are the complete filling of the FPD mould cavity, the filling time, the minimum amount of rejected material of the feeding system, defects due to air traps, welding lines, etc. As results, depending on the geometric complexity, and the number and position of the injection points, it is possible to reduce the rejected material and to improve the filling time of the FPD. es_ES
dc.language Inglés es_ES
dc.publisher Elsevier es_ES
dc.relation.ispartof Procedia Engineering es_ES
dc.rights Reconocimiento - No comercial - Sin obra derivada (by-nc-nd) es_ES
dc.subject Peek injection es_ES
dc.subject Injection process simulation es_ES
dc.subject Fixed partial dentures of peek es_ES
dc.subject.classification INGENIERIA DE LOS PROCESOS DE FABRICACION es_ES
dc.title Analysis of the feeding system in the injection process of peek in fixed partial dentures es_ES
dc.type Artículo es_ES
dc.type Comunicación en congreso es_ES
dc.identifier.doi 10.1016/j.proeng.2015.12.591 es_ES
dc.rights.accessRights Abierto es_ES
dc.contributor.affiliation Universitat Politècnica de València. Departamento de Ingeniería Mecánica y de Materiales - Departament d'Enginyeria Mecànica i de Materials es_ES
dc.description.bibliographicCitation Gutiérrez, SC.; Meseguer, MD.; Gandía Barberá, A. (2015). Analysis of the feeding system in the injection process of peek in fixed partial dentures. Procedia Engineering. 132:1021-1028. doi:10.1016/j.proeng.2015.12.591 es_ES
dc.description.accrualMethod S es_ES
dc.relation.conferencename 6th Manufacturing Engineering Society International Conference (MESIC 2015) es_ES
dc.relation.conferencedate July 22-24, 2015 es_ES
dc.relation.conferenceplace Barcelona, Spain es_ES
dc.relation.publisherversion https://doi.org/10.1016/j.proeng.2015.12.591 es_ES
dc.description.upvformatpinicio 1021 es_ES
dc.description.upvformatpfin 1028 es_ES
dc.type.version info:eu-repo/semantics/publishedVersion es_ES
dc.description.volume 132 es_ES
dc.relation.pasarela S\299789 es_ES


Este ítem aparece en la(s) siguiente(s) colección(ones)

Mostrar el registro sencillo del ítem