- -

Failure analysis of a plastic modular belt in-service

RiuNet: Institutional repository of the Polithecnic University of Valencia

Share/Send to

Cited by

Statistics

Failure analysis of a plastic modular belt in-service

Show simple item record

Files in this item

dc.contributor.author Sanchez-Caballero, Samuel es_ES
dc.contributor.author Sellés Cantó, Miguel Ángel es_ES
dc.contributor.author Ferrándiz Bou, Santiago es_ES
dc.contributor.author Peydro, M. A. es_ES
dc.contributor.author Oliver, B.A. es_ES
dc.date.accessioned 2019-05-08T20:31:40Z
dc.date.available 2019-05-08T20:31:40Z
dc.date.issued 2018 es_ES
dc.identifier.issn 1350-6307 es_ES
dc.identifier.uri http://hdl.handle.net/10251/120144
dc.description.abstract [EN] In this study, an analysis of the possible causes of the failure in-service of a section of a plastic modular belt was conducted. The study begins with a reproduction of the service conditions in a traction gear. An analysis of the fracture surfaces revealed the existence of defects in the interior of the parts. With the aim of determining the origin of the imperfections and their influence on the failure, an exhaustive mechanical and rheological characterization of the material was carried out. The development of an FE Analysis established that the reduction of the tensile strength of the part due to internal defects was around 70%. Tests also showed that the most stressed area was the area where the most defects appeared. A simulation of the injection process showed that the defects are caused by the geometry of the part, leading to the conclusion that its failure was caused by bad dimensioning of thicknesses. es_ES
dc.language Inglés es_ES
dc.publisher Elsevier es_ES
dc.relation.ispartof Engineering Failure Analysis es_ES
dc.rights Reconocimiento - No comercial - Sin obra derivada (by-nc-nd) es_ES
dc.subject Plastic modular belt es_ES
dc.subject Belt link es_ES
dc.subject Tensile test es_ES
dc.subject Rheology es_ES
dc.subject Injection simulation es_ES
dc.subject Defects es_ES
dc.subject Shrink cavity es_ES
dc.subject Air traps es_ES
dc.subject.classification INGENIERIA DE LOS PROCESOS DE FABRICACION es_ES
dc.subject.classification INGENIERIA MECANICA es_ES
dc.title Failure analysis of a plastic modular belt in-service es_ES
dc.type Artículo es_ES
dc.identifier.doi 10.1016/j.engfailanal.2018.06.019 es_ES
dc.rights.accessRights Abierto es_ES
dc.contributor.affiliation Universitat Politècnica de València. Departamento de Ingeniería Mecánica y de Materiales - Departament d'Enginyeria Mecànica i de Materials es_ES
dc.description.bibliographicCitation Sanchez-Caballero, S.; Sellés Cantó, MÁ.; Ferrándiz Bou, S.; Peydro, MA.; Oliver, B. (2018). Failure analysis of a plastic modular belt in-service. Engineering Failure Analysis. 93:13-25. https://doi.org/10.1016/j.engfailanal.2018.06.019 es_ES
dc.description.accrualMethod S es_ES
dc.relation.publisherversion https://doi.org/10.1016/j.engfailanal.2018.06.019 es_ES
dc.description.upvformatpinicio 13 es_ES
dc.description.upvformatpfin 25 es_ES
dc.type.version info:eu-repo/semantics/publishedVersion es_ES
dc.description.volume 93 es_ES
dc.relation.pasarela S\365634 es_ES


This item appears in the following Collection(s)

Show simple item record