Mostrar el registro sencillo del ítem
dc.contributor.advisor | Montañés Muñoz, Néstor | es_ES |
dc.contributor.advisor | Fenollar Gimeno, Octavio Ángel | es_ES |
dc.contributor.author | Pérez Guarner, Andrés | es_ES |
dc.date.accessioned | 2021-07-30T12:03:59Z | |
dc.date.available | 2021-07-30T12:03:59Z | |
dc.date.created | 2021-07-13 | |
dc.date.issued | 2021-07-30 | es_ES |
dc.identifier.uri | http://hdl.handle.net/10251/171025 | |
dc.description.abstract | [ES] El objetivo general de este proyecto se basa en el rediseño, análisis estructural y selección del proceso de fabricación de un fuselaje empleado en aeronaves de fotogrametría. En la fase de rediseño una de las condiciones que se establecerá, será la de obtener el mayor espacio interior manteniendo la resistencia estructural del fuselaje, pudiendo así albergar todos los componentes necesarios para la navegación del avión manteniendo su estabilidad estructural. El punto de partida es la selección de un fuselaje existente que se adapte a las exigencias establecidas y readaptarla con el fin de cumplir el resto de las condiciones. En cuanto a la fase de análisis, partiendo del diseño establecido en la etapa anterior, se procederá al análisis estructural del fuselaje mediante programas CAE, simulando el comportamiento del fuselaje ante cargas constantes, tensiones normales y tangenciales, etc. Tras la determinación de las tensiones que deberá soportar el fuselaje y el consecuente rediseño estructural, se pasará a la fase de selección de material donde se analizarán los materiales según los siguientes criterios: módulo específico, procesabilidad del material y coste del material teórico, entre otros. Por último, se acometerá la fase de selección del proceso de fabricación, en la que se tendrán presentes, entre otros, los siguientes aspectos: calidad del material tras el proceso, dificultad del proceso de fabricación y coste del proceso. | es_ES |
dc.description.abstract | [EN] The general objective of this project is based on the redesign, structural analysis, and selection of the manufacturing process of a fuselage used in photogrammetry aircraft. In the redesign phase, one of the conditions that will be established will be to obtain the largest interior space while maintaining the structural strength of the fuselage, thus being able to house all the components necessary for aircraft navigation while maintaining its structural stability. The starting point is the selection of an existing fuselage that meets the established requirements and retrofitting it to meet the rest of the conditions. Regarding the analysis phase, starting from the design established in the previous stage, the structural analysis of the fuselage will be carried out using CAE programs, simulating the behavior of the fuselage under constant loads, normal and tangential stresses, etc. After determining the stresses that the fuselage must withstand and the consequent structural redesign, the material selection phase will be passed where the materials will be analyzed according to the following criteria: specific module, material processability and theoretical material cost, among others. Finally, the selection phase of the manufacturing process will be undertaken, in which the following aspects will be considered, among others: quality of the material after the process, difficulty of the manufacturing process and cost of the process. | es_ES |
dc.description.abstract | [CA] L'objectiu general d'aquest projecte es basa en el redisseny, anàlisi estructural i selecció del procés de fabricació d'un fuselatge emprat en aeronaus de fotogrametria. En la fase de redisseny una de les condicions que s'establirà serà la d'obtindre el major espai interior mantenint la resistència estructural del fuselatge podent així albergar tots els components necessaris per a la navegació de l'avió mantenint la seua estabilitat estructural. El punt de partida és de la selecció d'un fuselatge existent que s'adapte a les exigències establides i readaptar-la amb la finalitat de complir la resta de les condicions. Quant a la fase d'anàlisi, partint del disseny establit en l'etapa anterior, es procedirà a l'anàlisi estructural del fuselatge mitjançant programes CAE, simulant el comportament del fuselatge davant càrregues constants, tensions normals i tangencials, etc. Després de la determinació de les tensions que haurà de suportar el fuselatge i el conseqüent redisseny estructural, es passarà a la fase de selecció de material on s'analitzaren els materials segons els següents criteris: Mòdul específic, procesabilitat del material i cost del material teòric, entre altres. Finalment, s'escometrà la fase de selecció del procés de fabricació, en la qual es tindran presents entre altres els següents aspectes: qualitat del material després del procés, dificultat del procés de fabricació i cost del procés. | es_ES |
dc.format.extent | 213 | es_ES |
dc.language | Español | es_ES |
dc.publisher | Universitat Politècnica de València | es_ES |
dc.rights | Reserva de todos los derechos | es_ES |
dc.subject | Fotogrametría | es_ES |
dc.subject | Diseño de aeronaves | es_ES |
dc.subject | Análisis estructural | es_ES |
dc.subject | Selección de materiales | es_ES |
dc.subject | Aeronaves | es_ES |
dc.subject | Aircraft design | es_ES |
dc.subject | Structural analysis | es_ES |
dc.subject | Materials selection | es_ES |
dc.subject | Aircraft | es_ES |
dc.subject | Photogrammetry | es_ES |
dc.subject.classification | CIENCIA DE LOS MATERIALES E INGENIERIA METALURGICA | es_ES |
dc.subject.other | Grado en Ingeniería Mecánica-Grau en Enginyeria Mecànica | es_ES |
dc.title | Rediseño, análisis estructural y selección del proceso de fabricación de un fuselaje empleado en aeronaves de fotogrametría | es_ES |
dc.type | Proyecto/Trabajo fin de carrera/grado | es_ES |
dc.rights.accessRights | Abierto | es_ES |
dc.description.bibliographicCitation | Pérez Guarner, A. (2021). Rediseño, análisis estructural y selección del proceso de fabricación de un fuselaje empleado en aeronaves de fotogrametría. Universitat Politècnica de València. http://hdl.handle.net/10251/171025 | es_ES |
dc.description.accrualMethod | TFGM | es_ES |
dc.relation.pasarela | TFGM\142011 | es_ES |