García-Asenjo, L.; Baselga, S.; Martínez, L.; Garrigues, P.; Luján, R. (2023). Design, establishment, analysis and quality control of a high-precision reference frame in Cortes de Pallás (Spain). En 5th Joint International Symposium on Deformation Monitoring (JISDM 2022). Editorial Universitat Politècnica de València. http://hdl.handle.net/10251/192314
Por favor, use este identificador para citar o enlazar este ítem: http://hdl.handle.net/10251/192314
Título:
|
Design, establishment, analysis and quality control of a high-precision reference frame in Cortes de Pallás (Spain)
|
Autor:
|
García-Asenjo, Luis
Baselga, Sergio
Martínez, Laura
Garrigues, Pascual
Luján, Raquel
|
Entidad UPV:
|
Universitat Politècnica de València. Centro de Investigación e Innovación en Bioingeniería - Centre de Recerca i Innovació en Bioenginyeria
Universitat Politècnica de València. Departamento de Ingeniería Cartográfica Geodesia y Fotogrametría - Departament d'Enginyeria Cartogràfica, Geodèsia i Fotogrametria
Universitat Politècnica de València. Escuela Técnica Superior de Ingeniería Geodésica, Cartográfica y Topográfica - Escola Tècnica Superior d'Enginyeria Geodèsica, Cartogràfica i Topogràfica
|
Fecha difusión:
|
|
Resumen:
|
[EN] A high-precision geodetic reference frame was required in Cortes de Pallás (Spain) to undertake a long-term deformation monitoring project. Involving distances up to 2000 m, the aimed accuracy was 1 mm and 3 mm for ...[+]
[EN] A high-precision geodetic reference frame was required in Cortes de Pallás (Spain) to undertake a long-term deformation monitoring project. Involving distances up to 2000 m, the aimed accuracy was 1 mm and 3 mm for horizontal and vertical components, respectively. Such a high precision is necessary to detect possible displacements of selected points on a critical rocky area in a short period of time, i.e. two or three years, and also to provide ground control for the integration of precise 3D models periodically obtained by remote sensing techniques. Considering the historical geotechnical problems of the area, the possible influence of the hydroelectric power plant, and the peculiar orography of the zone, a proper analysis of the stability is crucial if the reference frame is to be used for rigorous over-time deformation monitoring. This paper describes the deformation monitoring of a 10-pillar geodetic network which was measured from 2018 to 2020 by using a sub-millimetric Mekometer ME5000 (0.2 mm + 0.2 ppm) along with a demanding observing methodology which includes a network of data loggers for temperature, humidity and air pressure as well as proper calibration of sensors and instruments to prevent potential inconsistencies between the scale of the network and the unit of length of the International System (SI-metre). The results demonstrated that the chosen methodology yielded the aimed accuracy. However, using such a high precision methodology entails the problem that small displacements of only one or two millimeters are significantly detected as deformations by conventional deformation analysis and then it arises the problem of finding a subset of stable points for a rigorous datum realization when all the points seem to displace. This general problem is analyzed in the particular case of Cortes de Pallás, where a balanced mix of deformation analysis and technical decisions was eventually adopted to define a precise and stable reference frame for rigorous over-time deformation monitoring.
[-]
|
Palabras clave:
|
Geodetic network
,
Reference frames
,
Deformation monitoring
,
Sub-millimetric EDM
,
ME5000
,
Length metrology
|
Derechos de uso:
|
Reconocimiento - No comercial - Compartir igual (by-nc-sa)
|
ISBN:
|
9788490489796
|
Fuente:
|
5th Joint International Symposium on Deformation Monitoring (JISDM 2022).
|
Editorial:
|
Editorial Universitat Politècnica de València
|
Versión del editor:
|
http://ocs.editorial.upv.es/index.php/JISDM/JISDM2022/paper/view/13823
|
Título del congreso:
|
5th Joint International Symposium on Deformation Monitoring
|
Lugar del congreso:
|
València, España
|
Fecha congreso:
|
Junio 20-22, 2022
|
Código del Proyecto:
|
info:eu-repo/grantAgreement/Diputació de València//T-726/ES/Control de deformaciones en la ladera norte de la muela de Cortes de Pallás
info:eu-repo/grantAgreement/UPV//PAID-01-20/
|
Agradecimientos:
|
This work has been carried out under the contract T-726 – Control de deformaciones en la ladera norte de la muela de Cortes de Pallás commissioned by the Diputació de València. The authors are grateful to the UCM which ...[+]
This work has been carried out under the contract T-726 – Control de deformaciones en la ladera norte de la muela de Cortes de Pallás commissioned by the Diputació de València. The authors are grateful to the UCM which granted the use of its ME5000 Mekometer through a co-operation agreement, to José María Grima for his support to calibrate the ME5000 Mekometer, thermometers, and barometers at the Calibration Laboratory of the UPV. We also acknowledge IGS for their efforts to disseminate products available to the global community, and EURAMET for their contribution to the research efforts on the field of large-scale length metrology for geodesy. The UPV team acknowledge the Programa de Ayudas de Investigación y Desarrollo (PAID-01-20) de la Universitat Politècnica de València for funding the research contract of Raquel Luján
[-]
|
Tipo:
|
Capítulo de libro
Comunicación en congreso
|