Pereira, JC.; Zambrano, J.; Licausi, M.; Tobar, M.; Amigó Borrás, V. (2015). Tribology and high temperature friction wear behavior of MCrAlY laser cladding coatings on stainless steel. Wear. 330:280-287. https://doi.org/10.1016/j.wear.2015.01.048
Por favor, use este identificador para citar o enlazar este ítem: http://hdl.handle.net/10251/63388
Title:
|
Tribology and high temperature friction wear behavior of MCrAlY laser cladding coatings on stainless steel
|
Author:
|
Pereira, Juan Carlos
Zambrano, Jenny
Licausi, Marie-Pierre
Tobar, Maria
Amigó Borrás, Vicente
|
UPV Unit:
|
Universitat Politècnica de València. Instituto de Tecnología de Materiales - Institut de Tecnologia de Materials
Universitat Politècnica de València. Departamento de Ingeniería Mecánica y de Materiales - Departament d'Enginyeria Mecànica i de Materials
|
Issued date:
|
|
Abstract:
|
Temperature can have a significant effect on the extent of wear damage of metallic components. Thermal barrier coatings can improve the high temperature tribological and friction wear behavior. In this work the dry friction ...[+]
Temperature can have a significant effect on the extent of wear damage of metallic components. Thermal barrier coatings can improve the high temperature tribological and friction wear behavior. In this work the dry friction and wear behavior at low and high temperature of NiCoCrAlY and CoNiCrAlY laser cladding coatings were evaluated, as well as for the austenitic stainless steel AISI 304 used as substrate. Dense coatings, with good bonding to the substrate was obtained by coaxial laser cladding tracks (40% overlapping), with previously optimized laser parameters. Tribological wear tests were performed by sliding wear at room temperature and 500 ºC, with an Al2O3 ball on disk configuration tribometer. The wear scar surface was evaluated by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) microanalysis. The 3D topography of the wear track was determined by inductive contact profilometer which enabled the wear rate calculation. The microstructure of the coatings consists of γNi/β-NiAl or γCo/β-(Co,Ni)Al phases depending on the chemical composition of the alloy, as confirmed by X-ray diffraction (XRD) analysis. The wear test results show a reduction in wear rate at high temperature for all materials tested. For the NiCoCrAlY coating, the high temperature also reduces the friction coefficient, while it significantly increases the friction coefficient of CoNiCrAlY coating. The main damage mode is abrasion and adhesion, caused by the oxide and partially-oxidized particles in the contact surface. The coatings and substrate results were compared, resulting in an improved wear behavior.
[-]
|
Subjects:
|
Friction
,
Wear
,
MCrAlY
,
Laser cladding
,
Coating
|
Copyrigths:
|
Reserva de todos los derechos
|
Source:
|
Wear. (issn:
0043-1648
) (eissn:
1873-2577
)
|
DOI:
|
10.1016/j.wear.2015.01.048
|
Publisher:
|
Elsevier
|
Publisher version:
|
http://dx.doi.org/10.1016/j.wear.2015.01.048
|
Project ID:
|
info:eu-repo/grantAgreement/MICINN//MAT2011-28492-C03-03/ES/RECUBRIMIENTOS DE BARRERA TERMICA PARA LA MEJORA DE LAS PROPIEDADES SUPERFICIALES DE ACEROS AUSTENITICOS Y DUPLEX/
info:eu-repo/grantAgreement/MICINN//MAT2011-28492-C03-01/ES/CARACTERIZACION DE RECUBRRIMIENTOS DE BARRERA TERMICA OBTENIDOS POR LASER/
info:eu-repo/grantAgreement/GVA//ACOMP%2F2013%2F114/
info:eu-repo/grantAgreement/UC//CD3997-2011/
|
Thanks:
|
The authors acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03 and the Generalitat Valenciana through ACOMP/2013/114 support. ...[+]
The authors acknowledge the financial support of the Ministry of Science and Innovation of the Government of Spain through research project MAT2011-28492-C03 and the Generalitat Valenciana through ACOMP/2013/114 support. Professor Juan Carlos Pereira Falcon thanks the University of Carabobo (Grant CD3997-2011) for the financial support to pursue his doctoral studies at the UPV. Furthermore, the authors thank Dr. Jose Luis Jorda for the XRD analysis.
[-]
|
Type:
|
Artículo
|