Gómez-Zarzuela Quel, Consuelo(Universitat Politècnica de València, 2020-07-21)
[EN] The present PhD thesis aims at the development of a one-dimensional solver
capable of solving single- and two-phase flow fluid systems. The novelty of this
project lies in the use of an open source CFD platform, ...
Benajes Calvo, Jesus Vicente; Galindo Lucas, José; Fajardo, P.; Navarro García, Roberto(CASRPCenter of Advanced Scientific Research and Publications, 2014)
[EN] A steady multiple reference frame segregated compressible solver and an unsteady sliding mesh one are
developed using OpenFOAM® to simulate turbomachinery. For each of the two solvers, governing
equations, numerical ...
Bayón, Arnau; Vallés-Morán, F. J.; Macián Pérez, Juan Francisco; López Jiménez, Petra Amparo(International Association for Hydro-Environment Engineering and Research (IAHR), 2017)
[ES] La cuantificación de pérdidas de carga causadas por elementos singulares en instalaciones hidráulicas no puede realizarse determinísticamente, por lo que debe llevarse a cabo su ensayo en laboratorio. No obstante, ...
Salvador Rubio, Francisco Javier; Gimeno García, Jaime; Pastor Enguídanos, José Manuel; Martí Aldaraví, Pedro(Elsevier, 2014-10)
Simulating liquid spray first and second atomization is not an easy task. Many models have been developed over the past years, but Eulerian ones have proved their better performance for the dense zone of the spray. In this ...
Gregori Giménez, Josep(Universitat Politècnica de València, 2020-09-17)
[ES] La inyección de agentes extintores es una de las formas más comunes en las labores
de extinción de incendios. En el mundo aeronáutico, para la extinción de incendios
a bordo se ha utilizado tradicionalmente el Halon ...
Gil Juan, Mario(Universitat Politècnica de València, 2021-09-02)
[ES] El camino hacia utilizar agentes extintores de incendios limpios a bordo de las aeronaves pasa por el estudio minucioso de todo el proceso de inyección y la influencia de cada una de las propiedades de los fluidos ...
Martínez López, Jorge(Universitat Politècnica de València, 2013-05-30)
Durante el proceso de apertura y cierre de un inyector Diesel, las características del
combustible a la salida de la tobera cambian significativamente como consecuencia del
movimiento de la aguja. Este hecho tiene una ...
[ES] El objeto del presente trabajo es el estudio computacional, mediante CFD, del flujo
interno en una tobera de inyección diésel comercial con diferentes modelos
turbulentos mediante OpenFOAM y su comparación con un ...
Belda Pascual, Moises(Universitat Politècnica de València, 2019-10-31)
[EN] Due to the storms and the predictions of the rise in the mean sea water level, the overtopping rates that occur in some structures are inadmissible, as they jeopardize both the structural safety and that of people or ...
Sánchez Abad, Nour(Universitat Politècnica de València, 2017-02-13)
[EN] Air pollution is a constantly growing concern that industry and organisations need to face nowadays. It has been demonstrated that one of the major factors that contributes to the level of the air pollution comes from ...
AHERN, DECLAN ANTHONY(Universitat Politècnica de València, 2017-08-30)
Settling Tanks (STs) are used in wastewater treatment to improve water quality by elimination of suspended solids via gravitational settling. Gravitational separation processes and the internal hydrodynamics of the STs are ...
Pandal, Adrián; García-Oliver, José M; Pastor Enguídanos, José Manuel(SAGE Publications, 2020-01)
[EN] Diesel spray modeling is a multi-scale problem with complex interactions between different flow regions, that is, internal nozzle flow, near-nozzle region and developed spray, including evaporation and combustion. ...
Pandal Blanco, Adrián(Universitat Politècnica de València, 2014-05-19)
[ES] Durante el periodo de docencia del Máster el investigador se ha dedicado al estudio del modelado CFD de chorros Diesel bajo las condiciones de funcionamiento que se dan en los motores Diesel de inyección directa y al ...
Pandal Blanco, Adrián(Universitat Politècnica de València, 2016-09-01)
[EN] The main objective of this work is the modeling of diesel sprays under engine conditions, including the atomization, transport and evaporation processes pivotal in the diesel spray formation and its development. For ...
Winklinger, Johannes Franz(Universitat Politècnica de València, 2015-03-30)
El modelado CFD se ha convertido en una herramienta aceptada y ampliamente utilizada en el ámbito del diseño de motores de combustión interna alternativos. Los modelos de combustión avanzados ayudan a comprender los fenómenos ...
[EN] Background literature on the influence of parapets on the overtopping of mound breakwaters is limited. In this study, numerical tests were conducted using computational fluid dynamics (CFD) to analyze the influence ...
[EN] An accurate description of the hydrodynamics in the non-aerated region of the skimming flow on stepped spillways is of outmost importance, particularly in small structures at large discharges. In addition, the flow ...
Rojas Artuñedo, José Manuel(Universitat Politècnica de València, 2020-10-06)
[ES] Según la OMS (2019), las enfermedades cardiovasculares son la principal causa de fallecimiento en el mundo. Es por ello que el modelado de la circulación sanguínea en la aorta torácica de pacientes reales se ha ...
Desantes Fernández, José Mª; García-Oliver, José M; Pastor Enguídanos, José Manuel; Olmeda-Ramiro, Iván; Pandal, A.; Naud, B.(Elsevier, 2020-06)
[EN] Engine fuel spray modeling still remains a challenge, especially in the dense near-nozzle region. This region is difficult to experimentally access and also to model due to the complex and rapid liquid and gas ...
Casar Tena, Rodrigo Antonio(Universitat Politècnica de València, 2021-10-04)
[ES] Este Trabajo Final de Máster, basado en la mecánica de fluidos computacional, explora las bondades de las Large Eddy Simulation (LES) para captar, mediante el software de código libre OpenFOAM, la separación de flujo ...