- -

An Improved Tolerance Charting Technique Using an Analysis of Setup Capability

RiuNet: Repositorio Institucional de la Universidad Politécnica de Valencia

Compartir/Enviar a

Citas

Estadísticas

  • Estadisticas de Uso

An Improved Tolerance Charting Technique Using an Analysis of Setup Capability

Mostrar el registro sencillo del ítem

Ficheros en el ítem

[Cerrado]
Nombre: González - An ...
Tamaño: 694.2Kb
Formato: PDF
Descripción: Versión editorial
Solicitar una copia al autor
dc.contributor.author González Contreras, Francisco es_ES
dc.date.accessioned 2015-01-12T13:32:39Z
dc.date.available 2015-01-12T13:32:39Z
dc.date.issued 2012-10
dc.identifier.issn 0268-3768
dc.identifier.uri http://hdl.handle.net/10251/45999
dc.description.abstract The tolerance charting method enables the calculation of working tolerances in machining process planning. The method has been used as a basic tool for analysing process plans for many decades. Process capability in tolerance charting is modelled using the tolerances of the working dimensions. The literature shows that machining process capability can be analysed from the point of view of surface position errors. During setups it is possible to perform decomposition into two surface position tolerances: a datum surface position tolerance and a machining surface position tolerance. This type of analysis has the advantage of producing simplified tolerance chains. This paper provides an adaptation of the tolerance charting technique that uses a capability model based on datum and machining surface position tolerance. The results show an improvement in the working tolerance stackup that reduces the capability required for productive resources. As a result, reductions in manufacturing costs can be achieved. The proposal is valid for manual or computer-assisted techniques. es_ES
dc.description.sponsorship The translation of this paper was funded by Universidad Politecnica de Valencia, Spain. en_EN
dc.language Inglés es_ES
dc.publisher Springer Verlag (Germany) es_ES
dc.relation.ispartof International Journal of Advanced Manufacturing Technology es_ES
dc.rights Reserva de todos los derechos es_ES
dc.subject Tolerance charting es_ES
dc.subject Process capability es_ES
dc.subject Setup planning es_ES
dc.subject Locating error es_ES
dc.subject Machining process es_ES
dc.subject.classification INGENIERIA DE LOS PROCESOS DE FABRICACION es_ES
dc.title An Improved Tolerance Charting Technique Using an Analysis of Setup Capability es_ES
dc.type Artículo es_ES
dc.identifier.doi 10.1007/s00170-011-3874-5
dc.rights.accessRights Cerrado es_ES
dc.contributor.affiliation Universitat Politècnica de València. Departamento de Ingeniería Mecánica y de Materiales - Departament d'Enginyeria Mecànica i de Materials es_ES
dc.description.bibliographicCitation González Contreras, F. (2012). An Improved Tolerance Charting Technique Using an Analysis of Setup Capability. International Journal of Advanced Manufacturing Technology. 62(9-12):1205-1218. doi:10.1007/s00170-011-3874-5 es_ES
dc.description.accrualMethod S es_ES
dc.relation.publisherversion http://dx.doi.org/10.1007/s00170-011-3874-5 es_ES
dc.description.upvformatpinicio 1205 es_ES
dc.description.upvformatpfin 1218 es_ES
dc.type.version info:eu-repo/semantics/publishedVersion es_ES
dc.description.volume 62 es_ES
dc.description.issue 9-12 es_ES
dc.relation.senia 234216
dc.contributor.funder Universitat Politècnica de València
dc.description.references Xu HM, Yuan MH, Li DB (2009) A novel process planning schema based on process knowledge customization. Int J Adv Manuf Tech 44:161–172 es_ES
dc.description.references Rui W, Thimm G, Yongsheng M (2010) Review: geometric and dimensional tolerance modeling for sheet metal forming and integration with CAPP. Int J Adv Manuf Tech 51:871–889 es_ES
dc.description.references Jia HB, Xi FF, Ghasempoor A et al (2009) A tolerance method for industrial image-based inspection. Int J Adv Manuf Tech 43:11–12 es_ES
dc.description.references Martinez S, Cuesta E, Barreiro J et al (2010) Analysis of laser scanning and strategies for dimensional and geometrical control. Int J Adv Manuf Tech 46:621–629 es_ES
dc.description.references Janakiraman V, Saravanan R (2010) Concurrent optimization of machining process parameters and tolerance allocation. Int J Adv Manuf Tech 51:357–369 es_ES
dc.description.references Huang MF, Zhong YR (2008) Dimensional and geometrical tolerance balancing in concurrent design. Int J Adv Manuf Tech 35:723–735 es_ES
dc.description.references Hsieh KL (2006) The study of cost–tolerance model by incorporating process capability index into product lifecycle cost. Int J Adv Manuf Tech 28:638–642 es_ES
dc.description.references Huang MF, Zhong YR, Xu ZG (2005) Concurrent process tolerance design based on minimum product manufacturing cost and quality loss. Int J Adv Manuf Tech 25:714–722 es_ES
dc.description.references Motorcu AR, Gullu A (2006) Statistical process control in machining, a case study for machine tool capability and process capability. Mater Design 27:364–372 es_ES
dc.description.references Hamou S, Cheikh A, Linares JM et al (2004) Machining dispersions based procedures for computer aided process plan simulation. Int J Comput Integ M 17:141–150 es_ES
dc.description.references Jaballi K, Bellacicco A, Louati J et al (2009) Dimensioning of the intermediate states of the machined phases “DISMP” approach. Int J Adv Manuf Tech 45:907–921 es_ES
dc.description.references Nejad M, Vignat F, Villeneuve F (2009) Simulation of the geometrical defects of manufacturing. Int J Adv Manuf Tech 45:631–648 es_ES
dc.description.references Wan XJ, Xiong CH, Wang XF et al (2009) Analysis–synthesis of dimensional deviation of the machining feature for discrete-part manufacturing processes. Int J Mach Tool Manu 49:1214–1233 es_ES
dc.description.references Guo QJ, Yang JG, Wu H (2010) Application of ACO-BPN to thermal error modeling of NC machine tool. Int J Adv Manuf Tech 50:667–675 es_ES
dc.description.references Zhang YJ, Ge LL (2009) Selecting optimal set of tool sequences for machining of multiple pockets. Int J Adv Manuf Tech 42:233–241 es_ES
dc.description.references Ong TS, Hinds BK (2003) The application of tool deflection knowledge in process planning to meet geometric tolerances. Int J Mach Tool Manu 43:731–737 es_ES
dc.description.references Boyle I, Rong YM, Brown DC (2011) A review and analysis of current computer-aided fixture design approaches. Robot Cim-Int Manuf 27:1–12 es_ES
dc.description.references Bansal S, Nagarajan S, Reddy NV (2008) An integrated fixture planning system for minimum tolerances. Int J Adv Manuf Tech 38:501–513 es_ES
dc.description.references Chaiprapat S, Rujikietgumjorn S (2008) Modeling of positional variability of a fixtured workpiece due to locating errors. Int J Adv Manuf Tech 36:724–731 es_ES
dc.description.references Yao S, Han X, Yang Y et al (2007) Computer aided manufacturing planning for mass customization: part 2, automated setup planning. Int J Adv Manuf Tech 32:205–217 es_ES
dc.description.references Wang Y, Chen X, Gindy N (2007) Surface error decomposition for fixture development. Int J Adv Manuf Tech 31:948–956 es_ES
dc.description.references Qin GH, Zhang WH, Wan M (2006) A mathematical approach to analysis and optimal design of a fixture locating scheme. Int J Adv Manuf Tech 29:349–359 es_ES
dc.description.references Raghu A, Melkote SN (2005) Modeling of workpiece location error due to fixture geometric error and fixture-workpiece compliance. J Manuf Sci E-T ASME 127:75–83 es_ES
dc.description.references Kang Y, Rong Y, Yang JC (2003) Computer-aided fixture design verification. Part 2. Tolerance analysis. Int J Adv Manuf Tech 21:836–841 es_ES
dc.description.references Huang SH, Liu Q (2003) Rigorous application of tolerance analysis in setup planning. Int J Adv Manuf Tech 21:196–207 es_ES
dc.description.references Rong Y, Hu W, Kang Y et al (2001) Locating error analysis and tolerance assignment for computer-aided fixture design. Int J Prod res 39:3529–3545 es_ES
dc.description.references Rong Y (1997) Tolerance and accuracy analysis in computer-aided fixture design. In: Advanced tolerancing techniques. Wiley, New York, pp 381–425 es_ES
dc.description.references Huang SH, Zhang HC (1996) Tolerance analysis in setup planning for rotational parts. J Manuf Syst 15:340–350 es_ES
dc.description.references Zhang HC, Mei J, Dudek RA (1991) Cirp Ann-Manuf Techn 40:419–422 es_ES
dc.description.references Xue JB, Ji P (2005) Tolerance charting for components with both angular and square shoulder features. IIE TRANS 37:815–825 es_ES
dc.description.references Gao Y, Huang M (2003) Optimal process tolerance balancing based on process capabilities. Int J Adv Manuf Tech 21:501–507 es_ES
dc.description.references Xue JB, Ji P (2002) Identifying tolerance chains with a surface-chain model in tolerance charting. J Mater Process Tech 123:93–99 es_ES
dc.description.references Britton GA, Thimm G (2002) A matrix method for calculating working dimensions and offsets for tolerance charting. Int J Adv Manuf Tech 20:448–453 es_ES
dc.description.references Ji P, Xue JB (2002) Process tolerance control in a 2D angular tolerance chart. Int J Adv Manuf Tech 20:649–654 es_ES
dc.description.references Pan YR, Tang GR (2001) Computer-aided tolerance charting for products with angular features. Int J Adv Manuf Tech 17:361–370 es_ES
dc.description.references Xue JB, Ji P (2001) A 2D tolerance chart for machining angular features. Int J Adv Manuf Tech 17:523–530 es_ES
dc.description.references Khodaygan S, Movahhedy MR, Fomani MS (2010) Tolerance analysis of mechanical assemblies based on modal interval and small degrees of freedom (MI-SDOF) concepts. Int J Adv Manuf Tech 50:1041–1061 es_ES
dc.description.references Ngoi BKA, Ong JM (1999) A complete tolerance charting system in assembly. Int J Prod Res 37:2477–2498 es_ES
dc.description.references Dimitrellou SC, Diplaris SC, Sfantsikopoulos MM (2008) Tolerance elements: an alternative approach for cost optimum tolerance transfer. J Eng Design 19:173–184 es_ES
dc.description.references Contreras FG, Rosado P (2007) An alternative method to tolerance transfer for parts with 2D blueprint. Int J Prod Res 45:5309–5328 es_ES
dc.description.references Sfantsikopoulos MM, Diplaris SC (1991) Coordinate tolerancing in design and manufacturing. Robot Cim-Int Manuf 8:219–222 es_ES
dc.description.references Curtis MA (1988) Process planning. Wiley, New York es_ES


Este ítem aparece en la(s) siguiente(s) colección(ones)

Mostrar el registro sencillo del ítem