Morales-Casas, Adrián; Torims, Toms; Gutiérrez, S. C.(Trans Tech Publications, 2019)
[EN] This article presents the analysis and redesign of an equipment aimed at repairing in-situ the journal surface of a marine diesel engine crankshaft, based on laser cladding technology. The paper outlines the comprehensive ...
[EN] Free form surfaces are commonly used to generate aesthetic parts. These parts can be manufactured directly by material removal techniques or indirectly with molding or forming techniques. In any case, these surfaces ...
Gutiérrez, S. C.; Meseguer, M. D.; Gandía Barberá, Alejandro(Elsevier, 2015)
[EN] In dental sector, PEEK is a new material used in the injection process of fixed partial dentures (FPD). The design of the feeding system is one of the most important stages in the injection process. This study simulates ...
Gutiérrez, S. C.; Meseguer, M. D.; Bellera Sosa, Julio; Folguera Arbas, Fernando(Elsevier, 2013)
[EN] This article studies tridimensional adjustment of Cr-Co fixed partial dentures obtained with different manufacturing processes (CNC milling, laser metal sintering and lost-wax), making a special point of the most ...
Bellera Sosa, Julio Cesar(Universitat Politècnica de València, 2016-05-17)
En la siguiente tesina se describe un análisis del ajuste tridimensional entre los dientes pilares y las prótesis dentales fijas, obtenidas mediante diferentes procesos de fabricación (colada a la cera perdida, mecanizado ...
Gutiérrez Rubert, Santiago Carlos(Universitat Politècnica de València, 2008-05-07)
Una de las primeras etapas en la Planificación de Procesos asistida por ordenador, para procesos de mecanizado por arranque de material, consiste en identificar las zonas de material a eliminar en el bruto de partida para ...
Maz Zapater, Isabel(Universitat Politècnica de València, 2018-09-18)
[ES] El trabajo de fin de grado se basa en el análisis y la mejora del layout de la zona en la que se
producen los respaldos traseros del Mondeo para conseguir:
-Mejorar el flujo de material
-Unificar el flujo de los ...
González Simón, Javier(Universitat Politècnica de València, 2016-12-27)
[ES]
El objeto que se pretende en este trabajo es realizar una comparación de las protesis de puentes dentales, fabricados mediante tres procesos distintos de fabricación: colada a la cera perdida, fresado mediante control ...
TORRES GALLEGOS, SANDINO(Universitat Politècnica de València, 2016-03-14)
Este trabajo presenta el desarrollo de un sistema de fabricación aditiva adaptado a un brazo robótico Mitsubishi RV-2AJ de 5 grados de libertad, para conseguir un nuevo enfoque de diseño y fabricación aplicando estas ...
Gutiérrez, S. C.; Zotovic Stanisic, Ranko; Navarro, M.D.; Meseguer, M. D.(Elsevier, 2017)
[EN] The aim of this work is to manufacture a prototype of a lightweight robot arm with a low cost budget, fully functional. This prototype is used to test and fix the elements for driving and controlling. During the ...
[EN] This article describes a new, very low-cost torque sensor. It was designed to obtain a geometric shape suitable for very affordable manufacturing by machining. The torque sensor was developed under the principle of ...
Gutiérrez Rubert, Santiago Carlos; Meseguer Calas, María Desamparados; Estal, R.; Folguera, F.; Vidal, V.(American Institute of Physics (AIP), 2012)
[EN] Fixed partial dentures can be fabricated by means of different materials and with
different manufacturing processes. In order to establish possible differences among them, their
behaviour, as fatigue life or cement ...
Cerdá Ramón, Juan José(Universitat Politècnica de València, 2017-09-28)
[EN] Project focused as a guide of mold design where the different elements used in the manufacture of the mold, necessary calculations, design alternatives and options available for the correct operation of a mold for the ...
Torres, Sandino; Gutiérrez, S. C.(Universidad Nacional de Chimborazo, 2020-12-01)
[EN] This work presents a post-processor development for the use of a robot, Mitsubishi
RV-2AJ, in fused deposition modeling processes, FDM. For this purpose, a material
feeding and dragging system is designed and adapted ...
Sanchis Merino, Ignacio José(Universitat Politècnica de València, 2018-01-08)
[ES] Este Trabajo Final de Grado consistirá en el diseño de un sistema de arrastre de unas planchas de plástico mediante unos rodillos adherentes unidos por un eje que ejecuta su movimiento gracias a un motor; las planchas ...