Badía Valiente, José David; Strömberg, Emma Marie; Ribes Greus, María Desamparados; Karlsson, Sigbritt(ELSEVIER SCIENCE BV, 2011)
[EN] The sample preparation procedure for MALDI-TOF MS of polymers is addressed in this study by the application of a statistical Design of Experiments (DoE). Industrial poly (ethylene terephthalate) (PET) was chosen as ...
Vilaplana Domingo, Francisco Javier(Universitat Politècnica de València, 2008-05-30)
Polymers are subjected to physical and chemical changes during their processing, service life, and further recovery, and they may also interact with impurities that can alter their composition. These changes substantially ...
Martínez García-Llácer, Ana(Universitat Politècnica de València, 2017-03-01)
Imaginemos una población reducida y estabilizada, sin cultura del consumo, en
un marco económico que incorpora plenamente el impacto ambiental, en el que
el uso de los recursos es mínimo y el concepto de 'residuo' no ...
The study presented in this paper has been carried out using a highly fractional factorial experimental design. This design allows the analysis of a greater number of factors and levels with a reduced number of mixes. In ...
Martínez-Arranz, Sheila; Carrera, Nora; Albéniz, Ana C.; Espinet, Pablo; Vidal Moya, José Alejandro(Wiley-VCH Verlag, 2012-12)
[EN] The Stille coupling can be carried out in a batch process using insoluble tin supports. The
new type of support consists of stannylated polymers based on the vinylic polynorbornene skeleton that allow one to use a ...
García López, Cristina Gloria(Universitat Politècnica de València, 2015-05-11)
Nowadays environmental problems have become one of the most severe problems confronted by human
beings, and cannot be avoided wherever you are. Protect the earth as well as our shared living space has
to be the consensus ...
Verdejo Álvarez, Elena(Universitat Politècnica de València, 2018-10-15)
El área de nuestro proyecto se sitúa en el centro histórico de la ciudad de Valencia en el barrio del Carmen, concretamente en la manzana U-22 delimitada por las calles Guillem de Castro, Llíria, Gutenberg y Na Jordana, ...
Esteban Morcilo, Antonio(Universitat Politècnica de València, 2017-09-21)
[ES] Si se observa cómo ha evolucionado la arquitectura a lo largo del tiempo se aprecia la íntima relación de esta con las necesidades humanas de cada época, adaptándose a los acontecimientos sociales. Actualmente, la ...
Parres, F.; Crespo Amorós, José Enrique(Wiley-Blackwell, 2011-07-05)
This work was divided into three parts. First, high-impact polystyrene (HIPS) was submitted to a series of extrusion cycles with the objective of evaluating the consequent variations in its thermal and mechanical properties. ...
Manzano Hernández, Isabel(Universitat Politècnica de València, 2021-02-23)
[ES] A medida que la población mundial crece exponencialmente, las tasas de consumo y la demanda de nuevos productos también aumentan drásticamente. Como resultado, un gran número de productos al final de la vida útil (EoL) ...
Papariantafyllou, Eirini; Makropoulos, Christos(13th International Conference of Environmental Science and Technology, 2013-09-05)
In the context of water scarcity the interest in the reuse of treated wastewater as an alternative resource for non-potable uses has increased. Recent changes in the regulatory framework (JMD 145116/2011) and the introduction ...
Badía Valiente, José David; Monreal Mengual, Llúcia; Sáenz de Juano Arbona, Víctor; Ribes Greus, María Desamparados(Elsevier, 2014-09)
The effects of multiple mechanical recycling on amorphous polylactide (PLA) were simulated by means of
five successive injection-grinding cycles. The influence of the induced thermo-mechanical degradation
on the dielectric ...
García Alcaraz, Cristina(Universitat Politècnica de València, 2018-01-19)
[ES] El presente trabajo de fin de grado está destinado al diseño y realización de una gama de
contenedores de reciclaje domésticos (Contenedores de papel y cartón, envases y pilas). Estos
contenedores se diseñan con ...
Oliver Sabater, Edwin(Universitat Politècnica de València, 2019-09-06)
[ES] Este trabajo tiene como objetivo el estudio del diseño, cálculo y fabricación de una cubertería básica compuesta por tenedor, cuchara y cuchillo de un material termoplástico reciclable, teniendo en cuenta que su ...
Montoya Vergara, Cristina(Universitat Politècnica de València, 2020-11-02)
[ES] En la actualidad se producen gran cantidad de residuos a causa de nuestra forma de producir: economía lineal. Esta forma de producción debe evolucionar hacia otra que sea más sostenible, y por ello este proyecto ...
Serra Company, Júlia(Universitat Politècnica de València, 2020-01-29)
[ES] El TFG tiene como objetivo el desarrollo de una colección de textiles para el hogar con criterios de sostenibilidad, respetuoso con el medio ambiente. Se diseñará una colección que comprenda mantas de calada jacquard ...
Ibáñez Ruiz, Lucía(Universitat Politècnica de València, 2019-11-13)
[EN] This Master’s thesis analyzes the current state of the art of plastic packaging in relation to its recycling. The plastic sector is undergoing a crisis, it is under social pressure and it is within a context of ...
Moreno Esteve, María(Universitat Politècnica de València, 2020-06-22)
[ES] Análisis, ideación, experimentación, diseño y fabricación de productos de diseño (bolsos, mochilas, estuches) a partir de un proceso de supra-reciclaje de material publicitario en lona de PVC. Proyecto ecológico, ...
Sanchis Magraner, Jaime(Universitat Politècnica de València, 2019-10-04)
[ES] El uso masivo de plásticos es uno de los mayores problemas que afrontan las sociedades modernas actuales. Este uso está incentivado principalmente por el bajo coste de obtención y de procesamiento de los materiales ...
Vecina García, Rubén(Universitat Politècnica de València, 2020-10-02)
[ES] En un mundo donde cada vez son más evidentes los problemas medioambientales:
el cambio climático, los plásticos en nuestros océanos, los ríos repletos de residuos,
ciudades cuyo aire es cada vez menos puro y muchos ...